Samsung dishwasher is displaying an error code

Here's our reference list for dishwasher error codes, including troubleshooting steps to resolve them or links to the relevant guides.

Samsung dishwasher is displaying an error code

Important

Some models use blinking lights instead

If your model does not have a digital display, error codes will be communicated via flashing lights. See our other guide for interpreting them.

Don't try to reset or clear the code before you troubleshoot it

Always perform the correct troubleshooting before attempting to reset the dishwasher or clear the code. Otherwise the issue causing the error will not be addressed, which may cause the error to return or impair the dishwasher.

Select your error code for more information:

1E, IE - Clogged filter error (Waterwall models) or High temperature heater error (Rotary models)

Waterwall models:

Water is not making it through the filter.

Clean the fine filter at the bottom of the dishwasher. See your user manual for instructions.

If the code returns after the filter is cleaned, visit our Support Center to request service.

Rotary models:

The temperature inside the dishwasher is too hot.

  1. Switch the power to the dishwasher off (30 seconds) and then on again, at the circuit breaker.
  2. Empty the dishwasher.
  3. Fill the detergent drawer, and then start a Normal cycle.

If the error occurs again, visit our Support Center to request service.

3C - Pump operation error

The pump has failed.

Turn off the dishwasher, and then try to start the cycle again. If the error still occurs, visit our Support Center to request service.

3E - High temperature water supply error

The water is too hot.

Verify the hot water supply is not set above 176°F.

If it isn't, but the error still occurs, visit our Support Center to request service.

4C, 4E - Water supply error

The dishwasher is not getting water at the pressure or temperature that it needs.

See our guide for Dishwasher water supply requirements.

5C, SC, 5E, SE - Drain error

The dishwasher can't drain.

See our guide for dishwasher is not draining.

7E - Waterwall reflector error

The reflector is not able to move correctly.

See our guide for Waterwall reflector error.

9E - Low water level error

There is not enough water in the Dishwasher.

  1. Empty the dishwasher.
  2. Add detergent, and then run a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker, and visit our Support Center to request service.

AP - Access Point mode

The dishwasher is in Access Point Mode to assist with connecting to a mobile device.

If you are not trying to connect it, turn off the dishwasher and turn it back on again.

bE, 6E - Button error

The panel detects a stuck button.

  1. Turn off the dishwasher.
  2. Touch every button on the panel.

If any buttons are not working correctly, or the error code returns after turning the dishwasher back on, visit our Support Center to request service.

CE - Communication error

The control panel is unable to communicate with the rest of the dishwasher.

Turn off the dishwasher and try to start it again. If the error continues, visit our Support Center to request service.

HC - High temperature heater error

The temperature inside the dishwasher is too hot.

  1. Switch the power to the dishwasher off (30 seconds) and then on again, at the circuit breaker.
  2. Empty the dishwasher.
  3. Fill the detergent drawer, and then start a Normal cycle.

If the error occurs again, visit our Support Center to request service.

HE - Heater error

The temperature inside the dishwasher is being detected incorrectly.

  1. Empty the dishwasher.
  2. Add detergent, and then run a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker, and visit our Support Center to request service.

LC, LE - Leakage error

The dishwasher's leak sensor detects moisture. When this code occurs, the dishwasher will turn itself on and will not turn off. During this time it will attempt to drain the water away.

See our guide for dishwasher leaks and leak errors.

Note: On Waterwall models, this could also mean the water reflector is blocked, so also check that.

OC, 0C, oE - Over-level water error

There is more water in the dishwasher than there should be.

See our guide for dishwasher drain and overflow errors.

PC - Zone Wash error

The Zone Wash function is not operating correctly.

Turn off the dishwasher and then try to start the cycle again. If the error still occurs, visit our Support Center to request service.

PE - Half load function error

The half load function is not performing correctly.

  1. Empty the dishwasher.
  2. Add detergent and run a half load cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker, and visit our Support Center to request service.

tE - Temperature sensor error

The temperature inside the dishwasher is being detected incorrectly.

  1. Empty the dishwasher.
  2. Add detergent and run a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker, and visit our Support Center to request service.

Recommended Articles
How to reset your Samsung dishwasher
How to reset your Samsung dishwasher
Reset your dishwasher Resetting your dishwasher is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dishwasher (usually 1 to 5 minutes at most), and then power it up again. That's it. That's all it takes to reset. Find troubleshooting for your issue instead of just resetting Re
 How to reset your Samsung dishwasher
How to reset your Samsung dishwasher
How to reset your Samsung dishwasher When something goes wrong with your dishwasher, such as an error code or if it's not draining, you may think all that's needed is a good reset. A lot of the time, weird electronic glitches (such as those that might occur after a power outage) might be cleared with such a reset, but if this doesn't restart your d
 Lights are blinking on the Samsung dishwasher
Lights are blinking on the Samsung dishwasher
Some Samsung dishwasher models don't have a digital display, so error codes are displayed as blinking lights instead. The combination of blinking lights determines what the code is. However, since lights may blink as part of regular use, you should really only consider this an error code if the dishwasher isn't working normally, such as stopping mi
Was this content helpful?
We're here for you

Contact Samsung Support

Contact us online through chat and get support from an expert on your computer, mobile device or tablet. Support is also available on your mobile device through the Samsung Members App.
Get support
auto-contact_us-pc-2x auto-contact_us-pc-2x
flag
Go to site